Products

	__ __
Description	Description - __
Rating	Rating - __
Vendor	Vendor - __
Color	Color - __
	View full details

huawei

Huawei Switch S110-24T2SR (24*GE ports, 2*GE SFP ports, AC power)

(0)

LE 9,900.00

S110-24T2SR appearance

1	PWR indicator	2	Twenty-four GE electrical ports
3	Electrical port indicator	4	Two GE optical ports
5	Optical port indicator	6	Port mode switch button NOTE: Standard Mode: All ports are in the same VLAN, and the flow control function is enabled. Port Isolation: All downlink ports are isolated from each other and cannot communicate with each other. Downlink ports can communicate only with uplink ports. (The last two downlink electrical ports are not isolated.) Uplink ports are not isolated or aggregated. Uplink Aggregation: Two uplink optical ports are aggregated into a trunk interface. Eth-Trunk supports load balancing only based on source physical ports. Flow Control Disabling: All ports are in the same VLAN and flow control is disabled.
7	Ground screw	8	AC socket NOTE: Use the power cable delivered with the device.

Ports

Ports on the S110-24T2SR

Port	Connector Type	Description	Available Components
GE PoE+ electrical port	RJ45	A GE PoE+ electrical port sends and receives service data at 10/100/1000 Mbit/s.	Ethernet cable
GE optical port	SFP	A GE optical port can send and receive data at 100/1000 Mbit/s.	FE SFP/eSFP optical modules (only optical modules with transmission distances less than or equal to 15 km are supported) GE eSFP optical modules (only optical modules with transmission distances less than or equal to 10 km are supported)

Indicators and Buttons

Description of indicators on the device

Indicator	Color	Status	Description
PWR indicator	–	Off	The device is powered off.
PWR indicator	Green	Steady on	The power supply is normal.
Port indicator	–	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port. NOTE: During device startup, all port indicators are steady green for about 2 seconds and then off, indicating that service initialization is complete.
	Green	Blinking	The port is sending or receiving data.

Power Supply System

The device is powered by the power cable delivered with the device.

Heat Dissipation System

The device has no fans and uses natural heat dissipation.

Technical Specifications

Technical specifications of the S110-24T2SR

In stock

huawei

Huawei Switch S220-48P4X 48*GE ports(380W PoE+), 4*10GE SFP+ ports, built-in AC power)

(0)

LE 37,800.00

S220-48P4X

Overview

Table 4-42 Basic information about the S220-48P4X

Item	Details
Description	S220-48P4X (4810/100/1000BASE-T ports(380W PoE+), 410GE SFP+ ports, built-in AC power)
Part Number	98012378
Model	S220-48P4X
First supported version	V600R023C00

Components

Figure 4-15 S220-48P4X appearance

1	Forty-eight 10/100/1000BASE-T PoE+ ports	2	Four 10GE SFP+ ports
3	One console port	4	One MODE button
5	One RST button To reset the device, press the button. Resetting the device will cause service interruption.	6	Ground screw NOTE: It is used with a ground cable.
7	Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch.	8	AC socket NOTE: It is used with an AC power cable.

Ports

Table 4-43 Ports on the S220-48P4X

Port	Connector Type	Description	Available Components
10/100/1000BASE-T port	RJ45	A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s.	Ethernet cable
10GE SFP+ port	SFP+	A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.	GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module 10GE SFP+ optical modules 10GE-CWDM SFP+ optical modules 10GE-DWDM SFP+ optical modules 1 m and 3 m SFP+ high-speed copper cables 10 m SFP+ AOC cables
Console port	RJ45	The console port is connected to a console for on-site configuration.	Console cable

Indicators and Buttons

Figure 4-16 Indicators on the Switch

Table 4-44 Description of indicators on the switch

No.	Indicator	Name	Color	Status	Description
1	PWR	Power module indicator	–	Off	The switch is powered off.
1	PWR	Power module indicator	Green	Steady on	The power supply is normal.
2	SYS	System status indicator	–	Off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Steady on	During the system startup preparation phase, the SYS indicator is steady green, which lasts for a maximum of 30 seconds.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a fan alarm or a temperature alarm has been generated.
3	PoE	PoE indicator	–	Off	The PoE mode is not selected.
3	PoE	PoE indicator	Green	Steady on	The PoE mode is selected, and service port indicators show the PoE status of each port.
4	MODE	Mode switch button	–	–	If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode.
5	–	Electrical service port indicator (one indicator for each port)	Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.		Meanings of service port indicators vary in different modes. For details, see Table 4-45 and Table 4-46.
6	–	Optical service port indicator (two indicators for each port)	Each optical port has two single-color indicators. The one on the left is the ACT indicator (yellow), and the one on the right is the LINK indicator (green). Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top.
7	CLOUD	Cloud indicator	–	Off	The device is not in the cloud management state.
			Blue	Fast blinking	The device is connecting to the cloud.
			Blue	Slow blinking	The device is in the cloud management state.

Table 4-45 Description of service port indicators in different modes (one indicator for each port)

Display Mode	Color	Status	Description
Default mode	–	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port.
	Green	Blinking	The port is sending or receiving data.
PoE mode	–	Off	The port is not providing power to a powered device (PD).
	Green	Steady on	The port is providing power to a PD.
	Green	Blinking	The power of the PD connected to the port exceeds the power capacity of the port or the power threshold configured on the port. Alternatively, the PD does not comply with IEEE standards.

Table 4-46 Description of service port indicators in different modes (two indicators for each port)

Display Mode	Color	Status	Description
Default mode (LINK indicator)	–	Off	The port is not connected or has been shut down.
Default mode (LINK indicator)	Green	Steady on	A link has been established on the port.
Default mode (ACT indicator)	–	Off	The port is not connected or has been shut down, or no data is transmitted or received.
Default mode (ACT indicator)	Yellow	Blinking	The port is sending or receiving data.

Power Supply System

The switch has a built-in AC power module and does not support pluggable power modules. The built-in power module can provide 380 W PoE power, which ensures full PoE power on 24 ports in compliance with 802.3af or on 12 ports in compliance with 802.3at.

Heat Dissipation System

The switch has two built-in fans for forced air cooling. Air flows in from the left side, and exhausts from the right side.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 4-47 Technical specifications of the S220-48P4X

Item	Specification
Dimensions without packaging (H x W x D) [mm(in.)]	Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 220.0 mm (1.72 in. x 17.4 in. x 8.66 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the parts protruding from the rear panel): 43.6 mm x 442.0 mm x 227.0 mm (1.72 in. x 17.4 in. x 8.94 in.)
Dimensions with packaging (H x W x D) [mm(in.)]	90.0 mm x 550.0 mm x 360.0 mm (3.54 in. x 21.65 in. x 14.17 in.)
Chassis height [U]	1 U
Chassis material	Metal
Weight without packaging [kg(lb)]	3.24 kg (7.14 lb)
Weight with packaging [kg(lb)]	4.29 kg (9.46 lb)
Typical power consumption [W]	49.44 W
Typical heat dissipation [BTU/hour]	168.69 BTU/hour
Maximum power consumption [W]	Without PoE: 64.7 W Full PoE load: 462.80 W (PoE: 380 W)
Maximum heat dissipation [BTU/hour]	Without PoE: 220.76 Full PoE load: 1579.12
Static power consumption [W]	34.04 W
MTBF [years]	48.14 years
MTTR [hours]	2 hours
Availability	> 0.99999
Noise at normal temperature (acoustic power) [dB(A)]	49.3 dB(A)
Noise at normal temperature (acoustic pressure) [dB(A)]	37.3 dB(A)
Number of card slots	0
Number of power slots	0
Number of fans modules	2
Uplink ports	4 x 10GE SFP+ ports
Downlink ports	48 x 10/100/1000BASE-T ports (380 W, PoE+)
Redundant power supply	Not supported
Long-term operating temperature [°C(°F)]	-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5905.44 ft.)

Storage temperature [°C(°F)]	–40°C to +70°C (–40°F to +158°F)
Long-term operating relative humidity [RH]	5% RH to 95% RH (non-condensing)
Long-term operating altitude [m(ft.)]	0–5000 m (0–16404 ft.)
Storage altitude [m(ft.)]	0-5000 m (0-16404 ft.)
Power supply mode	AC built-in
Rated input voltage [V]	AC input: 100 V AC to 240 V AC, 50/60 Hz High-voltage DC input: 240 V DC
Input voltage range [V]	AC input: 90 V AC to 290 V AC; 45 Hz to 65 Hz High-voltage DC input: 190 V DC to 290 V DC
Maximum input current [A]	6 A
Memory	2 GB
Flash memory	Physical space: 1 GB
Console port	RJ45
Eth Management port	Not supported
USB	Not supported
RTC	Not supported
RPS input	Not supported
Service port surge protection [kV]	Common mode: ±7 kV
Power supply surge protection [kV]	Differential mode: ±6 kV; common mode: ±6 kV
Ingress protection level (dustproof/waterproof)	IP20
Types of fans	Built-in

In stock

huawei

Huawei Switch S220-48T4S (48*GE ports, 4*GE SFP ports, built-in AC power)

(0)

LE 18,500.00

S220-48T4S

Overview

Table 4-33 Basic information about the S220-48T4S

Item	Details
Description	S220-48T4S (4810/100/1000BASE-T ports, 4GE SFP ports, built-in AC power)
Part Number	98012380
Model	S220-48T4S
First supported version	V600R023C00

Components

Figure 4-12 S220-48T4S appearance

1	Forty-eight 10/100/1000BASE-T ports	2	Four 1000BASE-X ports
3	One console port	4	One MODE button NOTE: This button is reserved and is not required currently.
5	One RST button NOTICE: To restore the factory settings and reset the device, hold down the button for at least 6 seconds. To reset the device, press the button. Resetting the device will cause service interruption. Exercise caution when you press the button.	6	Ground screw NOTE: It is used with a ground cable.
7	Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch.	8	AC socket NOTE: It is used with an AC power cable.

Ports

Table 4-34 Ports on the S220-48T4S

Port	Connector Type	Description	Available Components
10/100/1000BASE-T port	RJ45	A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s.	Ethernet cable
1000BASE-X port	SFP	A 1000BASE-X port can send and receive data at 1000 Mbit/s.	GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module
Console port	RJ45	The console port is connected to a console for on-site configuration.	Console cable

Indicators and Buttons

The S220-48T4S has similar indicators to those on the S220-48P4X except that the S220-48T4S does not have a PoE mode indicator. For details, see the S220-48P4X.

Power Supply System

The switch has a built-in AC power module and does not support pluggable power modules.

Heat Dissipation System

The switch has a built-in fan for forced air cooling. Air flows in from the left side, and exhausts from the right side.

When working properly at a normal temperature, the device meets the desktop-class noise requirements. However, the fan speed may be high and the noise may be loud during device startup.

In stock

huawei

Huawei Switch S220-48T4X (48*GE ports, 4*10GE SFP+ ports, built-in AC power)

(0)

LE 21,450.00

S220-48T4X , a high-capacity network switch designed to accommodate the ever-growing demand for reliable and high-speed network connectivity. The S220-48T4X model is crafted to provide an exceptional networking foundation for enterprises seeking to enhance their operational efficiency and network performance.

Equipped with 48 Gigabit Ethernet ports, the Huawei S220-48T4X offers ample connectivity for a myriad of devices, making it an ideal choice for businesses with extensive networking requirements. These ports deliver fast and reliable data transfer, ensuring that all connected devices benefit from optimal performance.

In addition to its impressive array of Gigabit ports, the S220-48T4X boasts 4 10G SFP+ ports. These high-speed uplink ports are perfect for businesses that require fast data transfer rates for applications such as streaming, large file transfers, or data backups, providing a future-proof solution that supports the increasing demands for bandwidth.

The Huawei S220-48T4X is not just about sheer speed; it’s also about intelligent network management. With advanced Quality of Service (QoS) capabilities and Link Aggregation Control Protocol (LACP), it ensures that critical network traffic is prioritized and that data flows smoothly and efficiently across the network.

One of the key benefits of the Huawei S220-48T4X is its ease of integration into existing network infrastructures. Its intuitive management interface simplifies the complexities of network configuration, monitoring, and troubleshooting, allowing for seamless network administration and operation.

Durability and reliability are the cornerstones of the S220-48T4X’s design. It is engineered to endure the continuous operation demands of modern businesses, and its energy-efficient technologies help reduce operational costs while maintaining high performance.

Embrace the Huawei S220-48T4X for an advanced, scalable network solution that promises to keep pace with your company’s growth. This switch is not just a tool for today but an investment in your network’s future, designed to provide a stable and robust networking experience. Engage with us to discover the full potential of the Huawei S220-48T4X and how it can become the backbone of your business’s connectivity needs.

Overview

Table 4-36 Basic information about the S220-48T4X

Item	Details
Description	S220-48T4X (4810/100/1000BASE-T ports, 410GE SFP+ ports, built-in AC power)
Part Number	98012377
Model	S220-48T4X
First supported version	V600R023C00

Components

Figure 4-13 S220-48T4X appearance

1	Forty-eight 10/100/1000BASE-T ports	2	Four 10GE SFP+ ports
3	One console port	4	One MODE button NOTE: This button is reserved and is not required currently.
5	One RST button NOTICE: To restore the factory settings and reset the device, hold down the button for at least 6 seconds. To reset the device, press the button. Resetting the device will cause service interruption. Exercise caution when you press the button.	6	Ground screw NOTE: It is used with a ground cable.
7	Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch.	8	AC socket NOTE: It is used with an AC power cable.

Ports

Table 4-37 Ports on the S220-48T4X

Port	Connector Type	Description	Available Components
10/100/1000BASE-T port	RJ45	A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s.	Ethernet cable
10GE SFP+ port	SFP+	A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s.	GE eSFP optical modules GE-CWDM eSFP optical modules GE-DWDM eSFP optical modules GE SFP copper module 10GE SFP+ optical modules 10GE-CWDM SFP+ optical modules 10GE-DWDM SFP+ optical modules 1 m and 3 m SFP+ high-speed copper cables 10 m SFP+ AOC cables
Console port	RJ45	The console port is connected to a console for on-site configuration.	Console cable

Indicators and Buttons

The S220-48T4X has similar indicators to those on the S220-48P4X except that the S220-48T4X does not have a PoE mode indicator. For details, see the S220-48P4X.

Power Supply System

The switch has a built-in AC power module and does not support pluggable power modules.

Heat Dissipation System

The switch has a built-in fan for forced air cooling. Air flows in from the left side, and exhausts from the right side.

When working properly at a normal temperature, the device meets the desktop-class noise requirements. However, the fan speed may be high and the noise may be loud during device startup.

In stock

huawei

Huawei Switch S310-24P4S (24*GE ports, 4*GE SFP ports, PoE+, AC power)

(0)

LE 27,300.00

Table 4-81 Basic information about the S310-24P4S

Item	Details
Description	S310-24P4S (2410/100/1000BASE-T ports, 4GE SFP ports, PoE+, AC power)
Part Number	98012201
Model	S310-24P4S
First supported version	V600R022C10

In stock

Product Comparison

Collection description

Explore Related Collections

Collection description