Products

huawei

(0)

LE 5,430.00

Table 4-3 Basic information about the S220S-8T2J

Item	Details
Description	S220S-8T2J (810/100/1000BASE-T ports, 22.5GE SFP ports, built-in AC power, Fanless)
Part Number	98012453
Model	S220S-8T2J
First supported version	V600R024C00

In stock

huawei

Huawei SFP-GE-LX-SM1310

(0)

LE 1,582.00

tem	Value
Basic Information
Module name	SFP-GE-LX-SM1310
Part Number	02315200
Model	SFP-GE-LX-SM1310
Form factor	eSFP
Application standard	1000BASE-LX10/LH
Connector type	LC
Optical fiber type	SMF
Working case temperature [°C(°F)]	0°C to 70°C (32°F to 158°F)
Digital diagnostic monitoring (DDM)	Supported
Transmission rate [bit/s]	1 Gbit/s
Target transmission distance [km]	Single-mode fiber: 10 km
Transmitter Optical Characteristics
Center wavelength [nm]	1310 nm
Maximum Tx optical power [dBm]	-3.0 dBm
Minimum Tx optical power [dBm]	-9.0 dBm
Minimum extinction ratio [dB]	9 dB
Receiver Optical Characteristics
Rx sensitivity [dBm]	-20.0 dBm
Overload power [dBm]	-3.0 dBm

In stock

huawei

(0)

LE 11,400.00

Overview

Table 4-13 Basic information about the S110-16LP2SR

Item	Details
Description	S110-16LP2SR (1610/100/1000BASE-T ports, 2GE SFP ports, PoE+, AC power)
Part Number	98012197
Model	S110-16LP2SR

Components

Figure 4-6 S110-16LP2SR appearance

1	PWR indicator	2	Sixteen GE PoE+ electrical ports
3	Electrical port indicator	4	Two GE optical ports
5	Optical port indicator	6	Port mode switch button NOTE: Standard Mode: All ports are in the same VLAN, and the flow control function is enabled. Port Isolation: All downlink ports are isolated from each other and cannot communicate with each other. Downlink ports can communicate only with uplink ports. (The last two downlink electrical ports are not isolated.) Uplink ports are not isolated or aggregated. Uplink Aggregation: Two uplink optical ports are aggregated into a trunk interface. Eth-Trunk supports load balancing only based on source physical ports. Flow Control Disabling: All ports are in the same VLAN and flow control is disabled.
7	Port indicator status switch button NOTE: Port status: The port indicator indicates the data transmission status of the port. PoE status: The port indicator indicates the PoE status of the port.	8	Ground screw
9	AC socket NOTE: Use the power cable delivered with the device.	–	–

Ports

Table 4-14 Ports on the S110-16LP2SR

Port	Connector Type	Description	Available Components
GE PoE+ electrical port	RJ45	A GE PoE+ electrical port sends and receives service data at 10/100/1000 Mbit/s. The port supports the PoE function.	Ethernet cable
GE optical port	SFP	A GE optical port can send and receive data at 100/1000 Mbit/s.	FE SFP/eSFP optical modules (only optical modules with transmission distances less than or equal to 15 km are supported) GE eSFP optical modules (only optical modules with transmission distances less than or equal to 10 km are supported)

Port

Connector Type

Description

Available Components

GE PoE+ electrical port

RJ45

A GE PoE+ electrical port sends and receives service data at 10/100/1000 Mbit/s.

The port supports the PoE function.

GE optical port

SFP

A GE optical port can send and receive data at 100/1000 Mbit/s.

Indicators and Buttons

Table 4-15 Description of indicators on the device

Indicator	Color	Status	Description
PWR indicator	–	Off	The device is powered off.
PWR indicator	Green	Steady on	The power supply is normal.
Port indicator (Port status)	–	Off	The port is not connected or has been shut down.
	Green	Steady on	A link has been established on the port. NOTE: During device startup, all port indicators are steady green for about 2 seconds and then off, indicating that service initialization is complete.
	Green	Blinking	The port is sending or receiving data.
Port indicator (PoE status)	–	Off	The port is not supplying PoE power.
	Green	Steady on	The port is supplying power to the connected PD.
	Green	Blinking	The PoE power of the device is insufficient, and the port cannot provide power to the PD.

Low in stock

Product Comparison